0 Al=J!e8Ep Tţ }_I|+am_J*j"T߸ţ%/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */ /* * linux/mii.h: definitions for MII-compatible transceivers * Originally drivers/net/sunhme.h. * * Copyright (C) 1996, 1999, 2001 David S. Miller (davem@redhat.com) */ #ifndef __LINUX_MII_H__ #define __LINUX_MII_H__ #include #include /* Generic MII registers. */ #define MII_BMCR 0x00 /* Basic mode control register */ #define MII_BMSR 0x01 /* Basic mode status register */ #define MII_PHYSID1 0x02 /* PHYS ID 1 */ #define MII_PHYSID2 0x03 /* PHYS ID 2 */ #define MII_ADVERTISE 0x04 /* Advertisement control reg */ #define MII_LPA 0x05 /* Link partner ability reg */ #define MII_EXPANSION 0x06 /* Expansion register */ #define MII_CTRL1000 0x09 /* 1000BASE-T control */ #define MII_STAT1000 0x0a /* 1000BASE-T status */ #define MII_MMD_CTRL 0x0d /* MMD Access Control Register */ #define MII_MMD_DATA 0x0e /* MMD Access Data Register */ #define MII_ESTATUS 0x0f /* Extended Status */ #define MII_DCOUNTER 0x12 /* Disconnect counter */ #define MII_FCSCOUNTER 0x13 /* False carrier counter */ #define MII_NWAYTEST 0x14 /* N-way auto-neg test reg */ #define MII_RERRCOUNTER 0x15 /* Receive error counter */ #define MII_SREVISION 0x16 /* Silicon revision */ #define MII_RESV1 0x17 /* Reserved... */ #define MII_LBRERROR 0x18 /* Lpback, rx, bypass error */ #define MII_PHYADDR 0x19 /* PHY address */ #define MII_RESV2 0x1a /* Reserved... */ #define MII_TPISTATUS 0x1b /* TPI status for 10mbps */ #define MII_NCONFIG 0x1c /* Network interface config */ /* Basic mode control register. */ #define BMCR_RESV 0x003f /* Unused... */ #define BMCR_SPEED1000 0x0040 /* MSB of Speed (1000) */ #define BMCR_CTST 0x0080 /* Collision test */ #define BMCR_FULLDPLX 0x0100 /* Full duplex */ #define BMCR_ANRESTART 0x0200 /* Auto negotiation restart */ #define BMCR_ISOLATE 0x0400 /* Isolate data paths from MII */ #define BMCR_PDOWN 0x0800 /* Enable low power state */ #define BMCR_ANENABLE 0x1000 /* Enable auto negotiation */ #define BMCR_SPEED100 0x2000 /* Select 100Mbps */ #define BMCR_LOOPBACK 0x4000 /* TXD loopback bits */ #define BMCR_RESET 0x8000 /* Reset to default state */ #define BMCR_SPEED10 0x0000 /* Select 10Mbps */ /* Basic mode status register. */ #define BMSR_ERCAP 0x0001 /* Ext-reg capability */ #define BMSR_JCD 0x0002 /* Jabber detected */ #define BMSR_LSTATUS 0x0004 /* Link status */ #define BMSR_ANEGCAPABLE 0x0008 /* Able to do auto-negotiation */ #define BMSR_RFAULT 0x0010 /* Remote fault detected */ #define BMSR_ANEGCOMPLETE 0x0020 /* Auto-negotiation complete */ #define BMSR_RESV 0x00c0 /* Unused... */ #define BMSR_ESTATEN 0x0100 /* Extended Status in R15 */ #define BMSR_100HALF2 0x0200 /* Can do 100BASE-T2 HDX */ #define BMSR_100FULL2 0x0400 /* Can do 100BASE-T2 FDX */ #define BMSR_10HALF 0x0800 /* Can do 10mbps, half-duplex */ #define BMSR_10FULL 0x1000 /* Can do 10mbps, full-duplex */ #define BMSR_100HALF 0x2000 /* Can do 100mbps, half-duplex */ #define BMSR_100FULL 0x4000 /* Can do 100mbps, full-duplex */ #define BMSR_100BASE4 0x8000 /* Can do 100mbps, 4k packets */ /* Advertisement control register. */ #define ADVERTISE_SLCT 0x001f /* Selector bits */ #define ADVERTISE_CSMA 0x0001 /* Only selector supported */ #define ADVERTISE_10HALF 0x0020 /* Try for 10mbps half-duplex */ #define ADVERTISE_1000XFULL 0x0020 /* Try for 1000BASE-X full-duplex */ #define ADVERTISE_10FULL 0x0040 /* Try for 10mbps full-duplex */ #define ADVERTISE_1000XHALF 0x0040 /* Try for 1000BASE-X half-duplex */ #define ADVERTISE_100HALF 0x0080 /* Try fo