0x00 *l4( (  fB- \k_I|+t/* SPDX-License-Identifier: GPL-2.0-only */ /* * drivers/media/video/tvp514x.h * * Copyright (C) 2008 Texas Instruments Inc * Author: Vaibhav Hiremath * * Contributors: * Sivaraj R * Brijesh R Jadav * Hardik Shah * Manjunath Hadli * Karicheri Muralidharan */ #ifndef _TVP514X_H #define _TVP514X_H /* * Other macros */ #define TVP514X_MODULE_NAME "tvp514x" #define TVP514X_XCLK_BT656 (27000000) /* Number of pixels and number of lines per frame for different standards */ #define NTSC_NUM_ACTIVE_PIXELS (720) #define NTSC_NUM_ACTIVE_LINES (480) #define PAL_NUM_ACTIVE_PIXELS (720) #define PAL_NUM_ACTIVE_LINES (576) /* enum for different decoder input pin configuration */ enum tvp514x_input { /* * CVBS input selection */ INPUT_CVBS_VI1A = 0x0, INPUT_CVBS_VI1B, INPUT_CVBS_VI1C, INPUT_CVBS_VI2A = 0x04, INPUT_CVBS_VI2B, INPUT_CVBS_VI2C, INPUT_CVBS_VI3A = 0x08, INPUT_CVBS_VI3B, INPUT_CVBS_VI3C, INPUT_CVBS_VI4A = 0x0C, /* * S-Video input selection */ INPUT_SVIDEO_VI2A_VI1A = 0x44, INPUT_SVIDEO_VI2B_VI1B, INPUT_SVIDEO_VI2C_VI1C, INPUT_SVIDEO_VI2A_VI3A = 0x54, INPUT_SVIDEO_VI2B_VI3B, INPUT_SVIDEO_VI2C_VI3C, INPUT_SVIDEO_VI4A_VI1A = 0x4C, INPUT_SVIDEO_VI4A_VI1B, INPUT_SVIDEO_VI4A_VI1C, INPUT_SVIDEO_VI4A_VI3A = 0x5C, INPUT_SVIDEO_VI4A_VI3B, INPUT_SVIDEO_VI4A_VI3C, /* Need to add entries for * RGB, YPbPr and SCART. */ INPUT_INVALID }; /* enum for output format supported. */ enum tvp514x_output { OUTPUT_10BIT_422_EMBEDDED_SYNC = 0, OUTPUT_20BIT_422_SEPERATE_SYNC, OUTPUT_10BIT_422_SEPERATE_SYNC = 3, OUTPUT_INVALID }; /** * struct tvp514x_platform_data - Platform data values and access functions. * @clk_polarity: Clock polarity of the current interface. * @hs_polarity: HSYNC Polarity configuration for current interface. * @vs_polarity: VSYNC Polarity configuration for current interface. */ struct tvp514x_platform_data { /* Interface control params */ bool clk_polarity; bool hs_polarity; bool vs_polarity; }; #endif /* ifndef _TVP514X_H */ " l4( (  fD- ,  # SPDX-License-Identifier: GPL-2.0-only # # Solarflare device configuration # config NET_VENDOR_SOLARFLARE bool "Solarflare devices" default y help If you have a network (Ethernet) card belonging to this class, say Y. Note that the answer to this question doesn't directly affect the kernel: saying N will just cause the configurator to skip all the questions about Solarflare devices. If you say Y, you will be asked for your specific card in the following questions. if NET_VENDOR_SOLARFLARE config SFC tristate "Solarflare SFC9100/EF100-family support" depends on PCI depends on PTP_1588_CLOCK_OPTIONAL select MDIO select CRC32 select NET_DEVLINK help This driver supports 10/40-gigabit Ethernet cards based on the Solarflare SFC9100-family controllers. It also supports 10/25/40/100-gigabit Ethernet cards based on the Solarflare EF100 networking IP in Xilinx FPGAs. To compile this driver as a module, choose M here. The module will be called sfc. config SFC_MTD bool "Solarflare SFC9100-family MTD support" depends on SFC && MTD && !(SFC=y && MTD=m) default y help This exposes the on-board flash and/or EEPROM as MTD devices (e.g. /dev/mtd1). This is required to update the boot configuration under Linux, or use some older userland tools to update the firmware. config SFC_MCDI_MON bool "Solarflare SFC9100-family hwmon support" depends on SFC && HWMON && !(SFC=y && HWMON=m) default y help This exposes the on-board firmware-managed sensors as a hardware monitor device. config SFC_SRIOV bool "Solarflare SFC9100-family SR-IOV support" depends on SFC && PCI_IOV depends on INET default y help This enables support for the Single Root I/O Virtualization features, allowing accelerated network performance in virtuali