unsupported   0  0"l4()P@ ƝS hunsupported "lY>C]q@q.4☴o u_c# # Please note that the parameters in this configuration file control the # behavior of the tools from the shadow-utils component. None of these # tools uses the PAM mechanism, and the utilities that use PAM (such as the # passwd command) should therefore be configured elsewhere. Refer to # /etc/pam.d/system-auth for more information. # # # Delay in seconds before being allowed another attempt after a login failure # Note: When PAM is used, some modules may enforce a minimum delay (e.g. # pam_unix(8) enforces a 2s delay) # #FAIL_DELAY 3 # Currently FAILLOG_ENAB is not supported # # Enable display of unknown usernames when login(1) failures are recorded. # #LOG_UNKFAIL_ENAB no # Currently LOG_OK_LOGINS is not supported # Currently LASTLOG_ENAB is not supported # # Limit the highest user ID number for which the lastlog entries should # be updated. # # No LASTLOG_UID_MAX means that there is no user ID limit for writing # lastlog entries. # #LASTLOG_UID_MAX # Currently MAIL_CHECK_ENAB is not supported # Currently OBSCURE_CHECKS_ENAB is not supported # Currently PORTTIME_CHECKS_ENAB is not supported # Currently QUOTAS_ENAB is not supported # Currently SYSLOG_SU_ENAB is not supported # # Enable "syslog" logging of newgrp(1) and sg(1) activity. # #SYSLOG_SG_ENAB yes # Currently CONSOLE is not supported # Currently SULOG_FILE is not supported # Currently MOTD_FILE is not supported # Currently ISSUE_FILE is not supported # Currently TTYTYPE_FILE is not supported # Currently FTMP_FILE is not supported # Currently NOLOGINS_FILE is not supported # Currently SU_NAME is not supported # *REQUIRED* # Directory where mailboxes reside, _or_ name of file, relative to the # home directory. If you _do_ define both, MAIL_DIR takes precedence. # MAIL_DIR /var/spool/mail #MAIL_FILE .mail # # If defined, file which inhibits all the usual chatter during the login # sequence. If a full pathname, then hushed mode will be enabled if the # user's name or shell are found in the file. If not a full pathname, then # hushed mode will be enabled if the file exists in the user's home directory. # #HUSHLOGIN_FILE .hushlogin #HUSHLOGIN_FILE /etc/hushlogins # Currently ENV_TZ is not supported # Currently ENV_HZ is not supported # # The default PATH settings, for superuser and normal users. # # (they are minimal, add the rest in the shell startup files) #ENV_SUPATH PATH=/sbin:/bin:/usr/sbin:/usr/bin #ENV_PATH PATH=/bin:/usr/bin # # Terminal permissions # # TTYGROUP Login tty will be assigned this group ownership. # TTYPERM Login tty will be set to this permission. # # If you have a write(1) program which is "setgid" to a special group # which owns the terminals, define TTYGROUP as the number of such group # and TTYPERM as 0620. Otherwise leave TTYGROUP commented out and # set TTYPERM to either 622 or 600. # #TTYGROUP tty #TTYPERM 0600 # Currently ERASECHAR, KILLCHAR and ULIMIT are not supported # Default initial "umask" value used by login(1) on non-PAM enabled systems. # Default "umask" value for pam_umask(8) on PAM enabled systems. # UMASK is also used by useradd(8) and newusers(8) to set the mode for new # home directories if HOME_MODE is not set. # 022 is the default value, but 027, or even 077, could be considered # for increased privacy. There is no One True Answer here: each sysadmin # must make up their mind. UMASK 022 # HOME_MODE is used by useradd(8) and newusers(8) to set the mode for new # home directories. # If HOME_MODE is not set, the value of UMASK is used to create the mode. HOME_MODE 0700 # Password aging controls: # # PASS_MAX_DAYS Maximum number of days a password may be used. # PASS_MIN_DAYS Minimum number of days allowed between password changes. # PASS_MIN_LEN Minimum acceptable password length. # PASS_WARN_AGE Number of days warning given before a password expires. # PASS_MAX_DAYS 99999 PASS_MIN_DAYS 0 PASS_WARN_AGE 7 # Curre