enabled ==File not found. 7?l4()P@v`S 0a4()P@v`SAǾAFile not found. C beɾ;C/* SPDX-License-Identifier: GPL-2.0-only */ /* * IEEE802.15.4-2003 specification * * Copyright (C) 2007-2012 Siemens AG */ #ifndef NET_MAC802154_H #define NET_MAC802154_H #include #include #include #include #include /** * enum ieee802154_hw_addr_filt_flags - hardware address filtering flags * * The following flags are used to indicate changed address settings from * the stack to the hardware. * * @IEEE802154_AFILT_SADDR_CHANGED: Indicates that the short address will be * change. * * @IEEE802154_AFILT_IEEEADDR_CHANGED: Indicates that the extended address * will be change. * * @IEEE802154_AFILT_PANID_CHANGED: Indicates that the pan id will be change. * * @IEEE802154_AFILT_PANC_CHANGED: Indicates that the address filter will * do frame address filtering as a pan coordinator. */ enum ieee802154_hw_addr_filt_flags { IEEE802154_AFILT_SADDR_CHANGED = BIT(0), IEEE802154_AFILT_IEEEADDR_CHANGED = BIT(1), IEEE802154_AFILT_PANID_CHANGED = BIT(2), IEEE802154_AFILT_PANC_CHANGED = BIT(3), }; /** * struct ieee802154_hw_addr_filt - hardware address filtering settings * * @pan_id: pan_id which should be set to the hardware address filter. * * @short_addr: short_addr which should be set to the hardware address filter. * * @ieee_addr: extended address which should be set to the hardware address * filter. * * @pan_coord: boolean if hardware filtering should be operate as coordinator. */ struct ieee802154_hw_addr_filt { __le16 pan_id; __le16 short_addr; __le64 ieee_addr; bool pan_coord; }; /** * struct ieee802154_hw - ieee802154 hardware * * @extra_tx_headroom: headroom to reserve in each transmit skb for use by the * driver (e.g. for transmit headers.) * * @flags: hardware flags, see &enum ieee802154_hw_flags * * @parent: parent device of the hardware. * * @priv: pointer to private area that was allocated for driver use along with * this structure. * * @phy: This points to the &struct wpan_phy allocated for this 802.15.4 PHY. */ struct ieee802154_hw { /* filled by the driver */ int extra_tx_headroom; u32 flags; struct device *parent; void *priv; /* filled by mac802154 core */ struct wpan_phy *phy; }; /** * enum ieee802154_hw_flags - hardware flags * * These flags are used to indicate hardware capabilities to * the stack. Generally, flags here should have their meaning * done in a way that the simplest hardware doesn't need setting * any particular flags. There are some exceptions to this rule, * however, so you are advised to review these flags carefully. * * @IEEE802154_HW_TX_OMIT_CKSUM: Indicates that xmitter will add FCS on it's * own. * * @IEEE802154_HW_LBT: Indicates that transceiver will support listen before * transmit. * * @IEEE802154_HW_CSMA_PARAMS: Indicates that transceiver will support csma * parameters (max_be, min_be, backoff exponents). * * @IEEE802154_HW_FRAME_RETRIES: Indicates that transceiver will support ARET * frame retries setting. * * @IEEE802154_HW_AFILT: Indicates that transceiver will support hardware * address filter setting. * * @IEEE802154_HW_PROMISCUOUS: Indicates that transceiver will support * promiscuous mode setting. * * @IEEE802154_HW_RX_OMIT_CKSUM: Indicates that receiver omits FCS. * * @IEEE802154_HW_RX_DROP_BAD_CKSUM: Indicates that receiver will not filter * frames with bad checksum. */ enum ieee802154_hw_flags { IEEE802154_HW_TX_OMIT_CKSUM = BIT(0), IEEE802154_HW_LBT = BIT(1), IEEE802154_HW_CSMA_PARAMS = BIT(2), IEEE802154_HW_FRAME_RETRIES = BIT(3), IEEE802154_HW_AFILT = BIT(4), IEEE802154_HW_PROMISCUOUS = BIT(5), IEEE802154_HW_RX_OMIT_CKSUM = BIT(6), IEEE802154_HW_RX_DROP_BAD_CKSUM = BIT(7), }; /* Indicates that receiver omits FCS and xmitter will add FCS on it's own. */ #define IEEE802154_HW_OMIT_CKSUM (IEEE802154_HW_TX_