0
     	€ДГ923ВБА ›    	/* SPDX-License-Identifier: GPL-2.0 */
#ifndef _S3C_ADC_BATTERY_H
#define _S3C_ADC_BATTERY_H

struct s3c_adc_bat_thresh {
	int volt; /* mV */
	int cur; /* mA */
	int level; /* percent */
};

struct s3c_adc_bat_pdata {
	int (*init)(void);
	void (*exit)(void);
	void (*enable_charger)(void);
	void (*disable_charger)(void);

	const struct s3c_adc_bat_thresh *lut_noac;
	unsigned int lut_noac_cnt;
	const struct s3c_adc_bat_thresh *lut_acin;
	unsigned int lut_acin_cnt;

	const unsigned int volt_channel;
	const unsigned int current_channel;
	const unsigned int backup_volt_channel;

	const unsigned int volt_samples;
	const unsigned int current_samples;
	const unsigned int backup_volt_samples;

	const unsigned int volt_mult;
	const unsigned int current_mult;
	const unsigned int backup_volt_mult;
	const unsigned int internal_impedance;

	const unsigned int backup_volt_max;
	const unsigned int backup_volt_min;
};

#endif
     Ќ_’I|Ґ‰УMjqШ‚¦р¬чВБ      File not found.
     €ЕДѓy ГВБ  Р    /* SPDX-License-Identifier: GPL-2.0-only */
/*******************************************************************************

  Header file for stmmac platform data

  Copyright (C) 2009  STMicroelectronics Ltd


  Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
*******************************************************************************/

#ifndef __STMMAC_PLATFORM_DATA
#define __STMMAC_PLATFORM_DATA

#include <linux/platform_device.h>
#include <linux/phy.h>

#define MTL_MAX_RX_QUEUES	8
#define MTL_MAX_TX_QUEUES	8
#define STMMAC_CH_MAX		8

#define STMMAC_RX_COE_NONE	0
#define STMMAC_RX_COE_TYPE1	1
#define STMMAC_RX_COE_TYPE2	2

/* Define the macros for CSR clock range parameters to be passed by
 * platform code.
 * This could also be configured at run time using CPU freq framework. */

/* MDC Clock Selection define*/
#define	STMMAC_CSR_60_100M	0x0	/* MDC = clk_scr_i/42 */
#define	STMMAC_CSR_100_150M	0x1	/* MDC = clk_scr_i/62 */
#define	STMMAC_CSR_20_35M	0x2	/* MDC = clk_scr_i/16 */
#define	STMMAC_CSR_35_60M	0x3	/* MDC = clk_scr_i/26 */
#define	STMMAC_CSR_150_250M	0x4	/* MDC = clk_scr_i/102 */
#define	STMMAC_CSR_250_300M	0x5	/* MDC = clk_scr_i/122 */

/* MTL algorithms identifiers */
#define MTL_TX_ALGORITHM_WRR	0x0
#define MTL_TX_ALGORITHM_WFQ	0x1
#define MTL_TX_ALGORITHM_DWRR	0x2
#define MTL_TX_ALGORITHM_SP	0x3
#define MTL_RX_ALGORITHM_SP	0x4
#define MTL_RX_ALGORITHM_WSP	0x5

/* RX/TX Queue Mode */
#define MTL_QUEUE_AVB		0x0
#define MTL_QUEUE_DCB		0x1

/* The MDC clock could be set higher than the IEEE 802.3
 * specified frequency limit 0f 2.5 MHz, by programming a clock divider
 * of value different than the above defined values. The resultant MDIO
 * clock frequency of 12.5 MHz is applicable for the interfacing chips
 * supporting higher MDC clocks.
 * The MDC clock selection macros need to be defined for MDC clock rate
 * of 12.5 MHz, corresponding to the following selection.
 */
#define STMMAC_CSR_I_4		0x8	/* clk_csr_i/4 */
#define STMMAC_CSR_I_6		0x9	/* clk_csr_i/6 */
#define STMMAC_CSR_I_8		0xA	/* clk_csr_i/8 */
#define STMMAC_CSR_I_10		0xB	/* clk_csr_i/10 */
#define STMMAC_CSR_I_12		0xC	/* clk_csr_i/12 */
#define STMMAC_CSR_I_14		0xD	/* clk_csr_i/14 */
#define STMMAC_CSR_I_16		0xE	/* clk_csr_i/16 */
#define STMMAC_CSR_I_18		0xF	/* clk_csr_i/18 */

/* AXI DMA Burst length supported */
#define DMA_AXI_BLEN_4		(1 << 1)
#define DMA_AXI_BLEN_8		(1 << 2)
#define DMA_AXI_BLEN_16		(1 << 3)
#define DMA_AXI_BLEN_32		(1 << 4)
#define DMA_AXI_BLEN_64		(1 << 5)
#define DMA_AXI_BLEN_128	(1 << 6)
#define DMA_AXI_BLEN_256	(1 << 7)
#define DMA_AXI_BLEN_ALL (DMA_AXI_BLEN_4 | DMA_AXI_BLEN_8 | DMA_AXI_BLEN_16 \
			| DMA_AXI_BLEN_32 | DMA_AXI_BLEN_64 \
			| DMA_AXI_BLEN_128 | DMA_AXI_BLEN_256)

struct stmmac_priv;

/* Platfrom data for platform device structure's platform_data field */

struct stmmac_mdio_bus_data {
	unsigned int phy_mask;
	unsigned int has_xpcs;
	unsigned int xpcs_an_inband;
	int *irqs;
	int probed_phy_irq;
	bool needs_reset;
};

struct stmmac_dma_cfg {
	int pbl;
	int txpbl;
	int rxpbl;