0 * l4( (  fB- 584_I|+H /* SPDX-License-Identifier: GPL-2.0 */ #ifndef __LINUX_USB_ONBOARD_DEV_H #define __LINUX_USB_ONBOARD_DEV_H struct usb_device; struct list_head; #if IS_ENABLED(CONFIG_USB_ONBOARD_DEV) void onboard_dev_create_pdevs(struct usb_device *parent_dev, struct list_head *pdev_list); void onboard_dev_destroy_pdevs(struct list_head *pdev_list); #else static inline void onboard_dev_create_pdevs(struct usb_device *parent_dev, struct list_head *pdev_list) {} static inline void onboard_dev_destroy_pdevs(struct list_head *pdev_list) {} #endif #endif /* __LINUX_USB_ONBOARD_DEV_H */   h!k /* SPDX-License-Identifier: GPL-2.0-only */ /* include/linux/sm501.h * * Copyright (c) 2006 Simtec Electronics * Ben Dooks * Vincent Sanders */ extern int sm501_unit_power(struct device *dev, unsigned int unit, unsigned int to); extern unsigned long sm501_set_clock(struct device *dev, int clksrc, unsigned long freq); extern unsigned long sm501_find_clock(struct device *dev, int clksrc, unsigned long req_freq); /* sm501_misc_control * * Modify the SM501's MISC_CONTROL register */ extern int sm501_misc_control(struct device *dev, unsigned long set, unsigned long clear); /* sm501_modify_reg * * Modify a register in the SM501 which may be shared with other * drivers. */ extern unsigned long sm501_modify_reg(struct device *dev, unsigned long reg, unsigned long set, unsigned long clear); /* Platform data definitions */ #define SM501FB_FLAG_USE_INIT_MODE (1<<0) #define SM501FB_FLAG_DISABLE_AT_EXIT (1<<1) #define SM501FB_FLAG_USE_HWCURSOR (1<<2) #define SM501FB_FLAG_USE_HWACCEL (1<<3) #define SM501FB_FLAG_PANEL_NO_FPEN (1<<4) #define SM501FB_FLAG_PANEL_NO_VBIASEN (1<<5) #define SM501FB_FLAG_PANEL_INV_FPEN (1<<6) #define SM501FB_FLAG_PANEL_INV_VBIASEN (1<<7) struct sm501_platdata_fbsub { struct fb_videomode *def_mode; unsigned int def_bpp; unsigned long max_mem; unsigned int flags; }; enum sm501_fb_routing { SM501_FB_OWN = 0, /* CRT=>CRT, Panel=>Panel */ SM501_FB_CRT_PANEL = 1, /* Panel=>CRT, Panel=>Panel */ }; /* sm501_platdata_fb flag field bit definitions */ #define SM501_FBPD_SWAP_FB_ENDIAN (1<<0) /* need to endian swap */ /* sm501_platdata_fb * * configuration data for the framebuffer driver */ struct sm501_platdata_fb { enum sm501_fb_routing fb_route; unsigned int flags; struct sm501_platdata_fbsub *fb_crt; struct sm501_platdata_fbsub *fb_pnl; }; /* gpio i2c * * Note, we have to pass in the bus number, as the number used will be * passed to the i2c-gpio driver's platform_device.id, subsequently used * to register the i2c bus. */ struct sm501_platdata_gpio_i2c { unsigned int bus_num; unsigned int pin_sda; unsigned int pin_scl; int udelay; int timeout; }; /* sm501_initdata * * use for initialising values that may not have been setup * before the driver is loaded. */ struct sm501_reg_init { unsigned long set; unsigned long mask; }; #define SM501_USE_USB_HOST (1<<0) #define SM501_USE_USB_SLAVE (1<<1) #define SM501_USE_SSP0 (1<<2) #define SM501_USE_SSP1 (1<<3) #define SM501_USE_UART0 (1<<4) #define SM501_USE_UART1 (1<<5) #define SM501_USE_FBACCEL (1<<6) #define SM501_USE_AC97 (1<<7) #define SM501_USE_I2S (1<<8) #define SM501_USE_GPIO (1<<9) #define SM501_USE_ALL (0xffffffff) struct sm501_initdata { struct sm501_reg_init gpio_low; struct sm501_reg_init gpio_high; struct sm501_reg_init misc_timing; struct sm501_reg_init misc_control; unsigned long devices; unsigned long mclk; /* non-zero to modify */ unsigned long m1xclk; /* non-zero to modify */ }; /* sm501_init_gpio * * default gpio settings */ struct sm501_init_gpio { struct sm501_reg_init gpio_data_low; struct sm501_reg_init gpio_data_high; struct sm501_reg_init gpio_ddr_low; struct sm501_reg_init gpio_ddr_high; }; #define SM501_FLAG_SUSPEND_OFF (1<<4) /* sm501_platdata * * This is passed with the p