auto █©аюFile not found. ┬дц ┐}Я=баю&х/* SPDX-License-Identifier: GPL-2.0-only */ /* * Interface the generic pinconfig portions of the pinctrl subsystem * * Copyright (C) 2011 ST-Ericsson SA * Written on behalf of Linaro for ST-Ericsson * This interface is used in the core to keep track of pins. * * Author: Linus Walleij */ #ifndef __LINUX_PINCTRL_PINCONF_GENERIC_H #define __LINUX_PINCTRL_PINCONF_GENERIC_H #include #include struct device_node; struct pinctrl_dev; struct pinctrl_map; /** * enum pin_config_param - possible pin configuration parameters * @PIN_CONFIG_BIAS_BUS_HOLD: the pin will be set to weakly latch so that it * weakly drives the last value on a tristate bus, also known as a "bus * holder", "bus keeper" or "repeater". This allows another device on the * bus to change the value by driving the bus high or low and switching to * tristate. The argument is ignored. * @PIN_CONFIG_BIAS_DISABLE: disable any pin bias on the pin, a * transition from say pull-up to pull-down implies that you disable * pull-up in the process, this setting disables all biasing. * @PIN_CONFIG_BIAS_HIGH_IMPEDANCE: the pin will be set to a high impedance * mode, also know as "third-state" (tristate) or "high-Z" or "floating". * On output pins this effectively disconnects the pin, which is useful * if for example some other pin is going to drive the signal connected * to it for a while. Pins used for input are usually always high * impedance. * @PIN_CONFIG_BIAS_PULL_DOWN: the pin will be pulled down (usually with high * impedance to GROUND). If the argument is != 0 pull-down is enabled, * if it is 0, pull-down is total, i.e. the pin is connected to GROUND. * @PIN_CONFIG_BIAS_PULL_PIN_DEFAULT: the pin will be pulled up or down based * on embedded knowledge of the controller hardware, like current mux * function. The pull direction and possibly strength too will normally * be decided completely inside the hardware block and not be readable * from the kernel side. * If the argument is != 0 pull up/down is enabled, if it is 0, the * configuration is ignored. The proper way to disable it is to use * @PIN_CONFIG_BIAS_DISABLE. * @PIN_CONFIG_BIAS_PULL_UP: the pin will be pulled up (usually with high * impedance to VDD). If the argument is != 0 pull-up is enabled, * if it is 0, pull-up is total, i.e. the pin is connected to VDD. * @PIN_CONFIG_DRIVE_OPEN_DRAIN: the pin will be driven with open drain (open * collector) which means it is usually wired with other output ports * which are then pulled up with an external resistor. Setting this * config will enable open drain mode, the argument is ignored. * @PIN_CONFIG_DRIVE_OPEN_SOURCE: the pin will be driven with open source * (open emitter). Setting this config will enable open source mode, the * argument is ignored. * @PIN_CONFIG_DRIVE_PUSH_PULL: the pin will be driven actively high and * low, this is the most typical case and is typically achieved with two * active transistors on the output. Setting this config will enable * push-pull mode, the argument is ignored. * @PIN_CONFIG_DRIVE_STRENGTH: the pin will sink or source at most the current * passed as argument. The argument is in mA. * @PIN_CONFIG_DRIVE_STRENGTH_UA: the pin will sink or source at most the current * passed as argument. The argument is in uA. * @PIN_CONFIG_INPUT_DEBOUNCE: this will configure the pin to debounce mode, * which means it will wait for signals to settle when reading inputs. The * argument gives the debounce time in usecs. Setting the * argument to zero turns debouncing off. * @PIN_CONFIG_INPUT_ENABLE: enable the pin's input. Note that this does not * affect the pin's ability to drive output. 1 enables input, 0 disables * input. * @PIN_CONFIG_INPUT_SCHMITT: this will configure an input pin to run in * schmitt-trigger mode. If the schmitt-trigger has adjustable hysteresis, * the threshold value is given on a custom format as argument when * setting pins